A and H Models  
   
 

  Home > Lenz Digital Products > Lenz Accessory Modules



Accessory Decoders

These stationary decoders allow you to switch points, signals and lights using DCC accessory addresses.

Please note that the Lenz system uses addresses as specified by the NMRA Recommended practices.

On the Lenz system, locomotive addresses, accessory addresses and feedback addresses can all be used together with no conflicts so you can have loco number 1, point number 1 and feedback number 1 on the same layout without there being a problem.


DCC Digital Command Control Help This is a link to our DCC Help pages


ImageCodeNameDescriptionPriceQty 
11010 LA010
LENZ1101011010 LA010

Lenz 11010 LA010 Adaptor for connection of accessory decoders LS100 to DC point motors such as Tortoise, LGB and Kato Unitrack

LA010 Manual

£14.15
11100 LS100 Accessory decoder for 4 turnouts with feedback
LENZ1110011100 LS100 Accessory decoder for 4 turnouts with feedback

Lenz 11100 LS100 Accessory decoder for 4 turnouts with feedback 
 
Accessory decoders are the link between your NMRA DCC system and your functional devices (that is turnouts, signals, uncouplers, etc.) on your model train layout.
 
Accessory decoders receive commands sent from the command station via the power station and activate the drives of turnouts or other switching devices. For DIGITAL plus systems these switching commands are activated from input devices, such as, hand held controller LH100 or LH90 (or in connection with another, compatible digital system).
 
Dimensions: approximately 3.5 x 3.5” (90 x 90 mm)

3 Amp Maximum 16 v AC Power input needed

LS100 Manual

A & H Help page for the LS100

£78.95
11150 LS150 Accessory decoder for 6 turnouts
LENZ1115011150 LS150 Accessory decoder for 6 turnouts

Lenz 11150 LS150 Accessory decoder for 6 turnouts 
 
The DIGITAL plus LS150 turnout decoder provides cost effective turnout control for up to 6 independent turnouts.

  • Suitable for twin-coil snap action switch machines
  • Suitable for motorized switch machines
  • High current provision to support Peco and Atlas switch machines
  • The 6 turnout addresses can be sequential or up to 6 user selected addresses.
  • Control using separate push-buttons possible.
  • Configuring the LS150 does not require a separate programming track and the parameters can be changed at any time in the future even after installation

LS150 Manual

A & H Help page for LS150

£58.25
25150 LW150 Mimic panel module
LENZ2515025150 LW150 Mimic panel module

Lenz  25150 LW150 Mimic panel module.  Now Available

Construct a mimic panel for your layout using the LW150.  16 accessory addresses may be controlled (Points and signals).  32 LEDs can also be powered to show the position of the 16 accessories.  Modules may be combined to make larger panels.  German Manual only at present - English help for LW150

The LW150 connects to XpressNet through the LMAB connector on the Lenz LZV100 command station or through the 80152 LY152 faceplate.  Up to 31 XpressNet devices can be connected to a system.

 

£92.65
26160 Power supply for LW150
LENZ2616026160 Power supply for LW150

Lenz 26160 additional Power Supply for LW150 module.  Now Available

On a large system that uses a number of XpressNet devices you may find that you need additional power.  The LW150 has a socket that allows you to feed additional power into XpressNet using a 26160 transformer.

The LZV100 provides 300mA to XpressNet. Below is a table of XpressNet devices and the power that they use:

 

Item Connection Power requirement
LH100 Handset XpressNet (LMAB) 28mA
LH90 Handset XpressNet (LMAB) 18mA
LH01 Handset XpressNet (LMAB) 30mA
USB Interface XpressNet (LMAB) 21mA
LW150 without LEDs XpressNet (LMAB) 18mA
LW150 with LEDs XpressNet (LMAB) 39mA
LS100 Feedback connection RS 1.5mA
LR101 Feeback module RS 1.5mA
LV101 Booster CDE 10mA

£25.95
80145 LY145 LED Expansion set for LW150
LENZ8014580145 LY145 LED Expansion set for LW150

Lenz 80145 Expansion set for LW150 module.  

Ribbon cable and 32 yellow LEDs for illuminating the accessories on a mimic panel

£15.85
80150 Xpressnet Power booster with transformer
LENZ8015080150 Xpressnet Power booster with transformer

Lenz 80150  Xpressnet repeater and power supply

For large systems where there are many XpressNet devices you may exceed the power that the LZV100 provides for XpressNet use.  The 80150 XpressNet repeater boosts the power plus improves signal quality with processing and error checking.  Supplied with a UK plug.
 

The LZV100 provides 300mA to XpressNet. Below is a table of XpressNet devices and the power that they use:

Item Connection Power requirement
LH100 Handset XpressNet (LMAB) 28mA
LH90 Handset XpressNet (LMAB) 18mA
LH01 Handset XpressNet (LMAB) 30mA
USB Interface XpressNet (LMAB) 21mA
LW150 without LEDs XpressNet (LMAB) 18mA
LW150 with LEDs XpressNet (LMAB) 39mA
LS100 Feedback connection RS 1.5mA
LR101 Feeback module RS 1.5mA
LV101 Booster CDE 10mA

£54.65
80152 LA152 Adaptor including Front Panel
LENZ8015280152 LA152 Adaptor including Front Panel

Lenz 80152 LA152 Adaptor including Front Panel 

This adapter is used for connecting further input devices to XpressNet.

  • the LED is used for controlling the XpressNet voltage
  • two five-pin DIN sockets and one Western plug at the front for connecting manual controls to XpressNet
  • terminal screws for connecting XpressNet connections
£24.95


 
 Return to main site View Cart